Plate Nº 98 · recorded November 17, 2026
Chemistry & MaterialsReported finding
Certain nitrogen compounds impede waste plastic pyrolysis oil reuse
Korean experiments on 13 impurities found that certain nitrogen compounds, especially 2-methylpyridine, can block zeolite sites and cut light-olefin yields.
By James Calloway4 min read769 words
In brief
- Researchers individually tested 13 impurities in waste plastic pyrolysis oil using a zeolite catalyst.
- 2-methylpyridine sharply reduced catalytic performance, while benzonitrile had a relatively small effect.
- A 2024 process produced light olefins without additional hydroprocessing, but used only one type of pyrolysis oil.
- Higher nitrogen-impurity concentrations worsened degradation, while higher reaction temperatures mitigated it.
- ACS Catalysis published the study in 2026 under DOI 10.1021/acscatal.5c08941.

By James Calloway
Thirteen impurities added one at a time to waste plastic pyrolysis oil exposed a sharp divide: sulfur-, chlorine- and oxygen-containing compounds had relatively minor effects, while certain nitrogen compounds significantly reduced catalytic performance. Among the nitrogen compounds, 2-methylpyridine caused a pronounced decline, whereas benzonitrile had a relatively small effect.
That contrast is the study’s practical warning: total nitrogen content alone cannot predict how dirty a feedstock will be for a catalyst. The specific chemical form of nitrogen matters, as do the impurity’s concentration and other operating conditions.
The Korean team, led by Dr. Do Kyoung Kim of the Korea Research Institute of Chemical Technology, worked with a team led by Professor Tae Yong Kim of Korea University of Technology and Education. The researchers published their results in ACS Catalysis in 2026.
In 2024, the team reported a circulating fluidized-bed catalytic-cracking process that converted waste plastic pyrolysis oil into light olefins without an additional hydroprocessing stage, or extra chemical treatment. That earlier test used only one type of pyrolysis oil, so it could not show how changing impurity compositions affect performance.
From discarded plastic to chemical feedstock
Waste plastic pyrolysis oil comes from heating discarded plastics at high temperatures until they break down chemically. It can serve as an alternative to petroleum or naphtha, a petroleum-derived liquid used as an industrial feedstock. The attraction is straightforward: recyclers could turn discarded plastic waste into a feedstock for new chemicals.
Inside a reactor, a zeolite catalyst breaks large hydrocarbon molecules into smaller ones through catalytic cracking. This produces light olefins, basic feedstocks for plastics and chemical products. The researchers used the zeolite catalyst they had developed in 2024 for the impurity tests.
Waste-derived oil carries contaminants inherited from different plastics and their additives. Their types and concentrations change with the feedstock, so one oil’s performance cannot stand in for another’s. That variability makes impurity control essential for stable production rather than a minor housekeeping issue.
Why nitrogen compounds mattered
The researchers individually added 13 nitrogen-, sulfur-, chlorine- and oxygen-containing impurities to actual waste plastic pyrolysis oil. They then compared light-olefin yields and product distributions using the 2024 zeolite catalyst. Sulfur, chlorine and oxygen compounds changed performance relatively little; particular nitrogen compounds did not.
To investigate why, the team used a machine-learning potential, an AI-based computational-chemistry technique that estimates molecular interactions. The model compared how strongly nitrogen impurities and the oil’s hydrocarbons attach to the catalyst’s active sites, meaning the places where cracking reactions occur.
When nitrogen compounds reached those sites first, they blocked access for the hydrocarbons that should react. Fewer available sites meant lower product yields. The analysis also showed that molecular size and the catalyst’s internal spatial environment influenced how much performance disappeared. Size still matters.
How operating conditions changed the damage
Higher concentrations of nitrogen impurities produced greater degradation. Raising the reaction temperature reduced the effect, giving operators one potential adjustment. The research also examined catalysts that had lost activity after repeated use: regeneration, which removes carbon-rich coke deposits, restored their initial performance.
Together, those observations support continuous catalyst regeneration in a circulating fluidized-bed process, where catalyst particles move with the material being processed. The practical promise is feedstock-specific impurity control rather than a single blanket limit. The catch: the tests establish a basis for prediction, not equal performance from every waste stream.
What does this change for plastic recyclers?
For operators, the next step is to characterize both the amount and identity of nitrogen compounds in each pyrolysis oil. The findings are expected to support impurity management, pretreatment optimization and adjustment of operating conditions. That could help plants avoid treating all contaminated oils alike when planning catalyst use and maintenance.
The regeneration result matters because it points toward recovery rather than simple catalyst replacement after deactivation. Still, the study does not turn experimental findings into a turnkey industrial recipe. Feedstocks remain variable, and the researchers tested added impurities individually, so the described work does not establish how mixtures behave.
The authors frame the contribution as a scientific basis for assessing whether waste plastic pyrolysis oil suits a particular catalytic process. The expected benefit is a workflow of measuring contaminants, accounting for their chemistry and tailoring the process, not a guarantee that every waste stream will produce the same yields.
Publication details
- Paper: Xuan Tin Tran et al., “Impact of Nitrogen and Other Heteroatoms on Catalytic Cracking of Crude Waste Plastic Pyrolysis Oil for Light-Olefin Production,” ACS Catalysis (2026).
- DOI: 10.1021/acscatal.5c08941
via phys.org/rss-feed/ (Source)
More from James Calloway
Show full bio
Staff writer covering regulation, policy and their impact on general science news at SciBeat.
473 articles
Nearby plates
- Molten Salt Process Turns Plastic Bags Into Gasoline at Oven Temperatures
- NUS Catalyst Regeneration Keeps Hydrogen Output Alive for 2,000 Hours
- New polystyrene is half plant-based and designed to fall apart for recycling
- Sulfur-Powered Material Splits Water Into Hydrogen Using Sunlight
- Self-Assembling Molecular Fabric Absorbs 97.9% of Benzene in Nylon Feedstock