Plate Nº 72 · recorded November 17, 2026
PhysicsReported finding
New Detector Counts Up to 9,000 Photons With Sub-Photon Precision
Paderborn University researchers built a detector that counts up to 9,000 photons, measuring up to 276 with sub-photon uncertainty using 1,024 detection bins instead of 37,000.
By Nathan Brooks3 min read664 words
In brief
- The detector counts photons from zero to more than 9,000, with precise counts up to 276 photons at sub-photon uncertainty.
- The system splits light into 128 time-separated pulses across 8 SNSPD detectors, creating 1,024 detection bins.
- A conventional multiplexed system would need roughly 37,000 detector elements to match the precision.
- Findings were published in Optica (DOI: 10.1364/OPTICA.604389) by a Paderborn University team.
- The system has so far only been tested on laser pulses averaging 1 to 15,000 photons.

A new photon detector can count light particles across a range from zero to more than 9,000, its builders at Paderborn University in Germany report. In tests, it measured pulses with uncertainty below a single photon — while precise counting reached up to 276 photons at once.
That precision matters for scientists building quantum computers and ultra-sensitive cameras, because those machines need to tally individual particles of light even when thousands arrive together. The findings appeared in Optica, Optica Publishing Group's journal for high-impact research, under the title "Macroscopic photon counting beating the Poisson noise limit" (DOI: 10.1364/OPTICA.604389).
"Precisely counting photons becomes more challenging as their numbers increase," said Timon Schapeler from Paderborn University. "Our approach extends photon counting to larger numbers of photons, bridging the gap between single-photon measurements and high-sensitivity optical power meters."
Why conventional detectors fall short
Standard devices simply can't do this job well. Avalanche photodiodes — semiconductor sensors that trigger an electrical cascade when light hits them — typically register whether light is present, but not how many photons arrived. Detectors built for brighter light run into a different wall: electrical noise drowns out the signal from individual photons, making them impossible to tell apart.
The Paderborn team attacked both problems by combining two tools. The first is superconducting nanowire single-photon detectors, or SNSPDs — hair-thin supercooled wires known for their efficiency, precise timing and low noise. The second is multiplexing, a technique that splits one signal into many parallel measurements.
"We wanted to know how high we can push the number of photons that can be counted with SNSPDs," Schapeler said. "This led to a detector system that uses multiplexing and the intrinsic photon-number resolution of SNSPDs."
He notes the scale is new. Although researchers had studied both technologies separately, nobody had previously demonstrated them together at this scale — an order of magnitude larger than earlier multiplexed single-photon counting systems.
How do you count 9,000 photons at once?
The system works by dividing and spreading the light. The team split a single light pulse into 128 smaller pulses separated in time, then distributed those across eight detectors. The result: 1,024 detection bins, each tracking how many photons landed in it.
"Our approach uses low-loss optical components to distribute light evenly across 1,024 detection bins while preserving photon-number information in each bin," said Tim Bartley from Paderborn University. "This enables precise measurements, while multiplexing expands the range of photon numbers the system can measure."
Earlier work had shown that SNSPDs could distinguish small numbers of photons using precise timing measurements. The new setup scales that idea up dramatically.
To sharpen accuracy further, the researchers used a detector model previously developed with Mariia Sidorova from PTB, Germany's national metrology institute, to characterize each detection bin. They then tested the system on laser pulses averaging between 1 and 15,000 photons.
The efficiency gain is striking. Matching this precision with a conventional multiplexed setup would take roughly 37,000 detector elements — about 36 times the 1,024 bins the German team actually used.
What could this enable?
The immediate target is photonic quantum computing — machines that process information using light rather than electrons.
"Large-scale measurement of individual photons is a cornerstone of photonic quantum computing and single-photon-level imaging," Bartley said. "With this new macroscopic photon-counting technology, we can learn a lot about how photonic quantum computers and single-photon-sensitive cameras can be scaled."
There are caveats worth flagging. The system has so far only been tested with laser pulses, not with the exotic quantum light states it's ultimately meant to probe. Next, the researchers plan to apply it to bright quantum states of light to investigate quantum effects at larger scales.
If SNSPD technology keeps improving, the team says the same approach could also support more precise, highly sensitive measurements across a range of sensing applications beyond quantum computing.
via google.com (Original)
More from Nathan Brooks
Show full bio
Market editor covering companies, deals and strategy in general science news at SciBeat.
456 articles
Nearby plates
- New Detector System Counts More Than 9,000 Individual Photons
- Purdue Tackles Three Big Roadblocks in Light-Powered Quantum Chips
- Laser 'Nuisance' Speckle Powers Record 6-Femtometer Spectrometer
- A quantum computer is being wired into an electron microscope
- Quantum Computer Operates in Orbit for the First Time