Plate Nº 28 · recorded November 16, 2026
Chemistry & MaterialsReported finding
New magnet method cuts dysprosium use by as much as 80%
A DGIST-led team redesigned the surface diffusion source for Nd–Fe–B magnets, cutting dysprosium use by as much as 80% while reporting equivalent magnetic performance.
By James Calloway3 min read655 words
In brief
- Dysprosium use fell by as much as 80% compared with a conventional dysprosium-only treatment.
- The redesigned diffusion source promoted thin, uniform shells and suppressed heavy-element accumulation near the magnet surface.
- The team reported magnetic performance equivalent to the conventional method.
- The paper appeared in Chemical Engineering Journal in 2026 with DOI 10.1016/j.cej.2026.182977.

By James Calloway
A research team cut dysprosium use by as much as 80% in neodymium–iron–boron permanent magnets while reporting magnetic performance equivalent to a conventional treatment. The 2026 result could ease a costly materials bottleneck, but the announcement offers no evidence of commercial-scale manufacturing.
Why does dysprosium matter?
Neodymium–iron–boron (Nd–Fe–B) magnets are key components in electric vehicle traction motors and wind turbines. Manufacturers add heavy rare-earth elements to preserve coercivity, which means resistance to demagnetization. That resistance must remain even at high temperatures.
Those heavy elements are extremely expensive, and their supply chains are unstable, placing a significant burden on industry. Completely removing them remains difficult. The practical challenge is therefore to use less while keeping the same magnetic performance.
How does the team reduce waste?
A widely used process is grain boundary diffusion. Processors apply heavy rare-earth elements to the magnet’s surface, then heat the magnet so those elements move into its interior. There, they travel along boundaries between crystal grains and form thin shells on the grain surfaces. The shells improve magnetic performance.
The waste starts when diffusion becomes uneven. Heavy elements can accumulate excessively within grains near the surface, making the shells unnecessarily thick. More material is not more performance. It means spending more on a scarce, costly ingredient.
A team led by Jeongmin Kim and Donghwan Kim of the Division of Nanotechnology at DGIST identified the causes of this excessive consumption. It redesigned the composition of the surface diffusion source, taking into account the proportion of light rare-earth elements in the base magnet.
That adjustment suppressed heavy-element accumulation near the surface and promoted thin, uniform shells on the grain surfaces. The team says this maximizes the efficiency of heavy rare-earth use. In less scientific language: it puts the costly material where it can do useful work, rather than wasting it inside near-surface grains.
What changed in the experiment?
When the team applied its new design, it reduced dysprosium use by as much as 80% compared with the conventional approach using dysprosium alone. The team also reported excellent magnetic performance equivalent to that conventional method.
Principal researcher Jeongmin Kim said: "This study presents a materials design strategy that can dramatically reduce the use of expensive heavy rare-earth elements by precisely controlling their movement and distribution."
Kim added: "We aim to extend this approach to light rare-earth–based processes, contributing to the efficient utilization of rare-earth resources and strengthening the technological competitiveness of next-generation high-performance permanent magnets."
The announcement gives no numerical magnetic measurements, so "equivalent" cannot be independently judged from the reported material.
What does this change for magnet makers?
It offers a practical design guideline: tailor the diffusion source to the light rare-earth composition of the base magnet. A manufacturer could therefore need less dysprosium without sacrificing the magnetic performance reported in this study. That is the immediate promise.
The announcement does not provide a baseline dysprosium amount, magnet grade, processing temperature, cost calculation, durability result, manufacturing trial, or independent replication. It also describes no traction-motor or wind-turbine test. "As much as 80%" describes the largest reported reduction, not a universal saving. Commercial readiness remains unshown.
The longer-term goal goes further. The researchers expect the findings to provide a foundation for next-generation magnet manufacturing based only on inexpensive light rare-earth elements, without heavy rare-earth elements. That remains a development target, not a demonstrated result.
What has been published?
The paper, "Compositionally tailored Dy–LRE–Zn–Cu diffusion sources for efficient grain boundary diffusion and reduced Dy consumption in Nd–Fe–B magnets," appears in Chemical Engineering Journal in 2026. Hyeonjong Jeong et al. wrote the paper.
In the title, Dy means dysprosium, LRE means light rare earth, and Zn and Cu mean zinc and copper. The DOI is 10.1016/j.cej.2026.182977.
via phys.org/rss-feed/ (Source)
More from James Calloway
Show full bio
Staff writer covering regulation, policy and their impact on general science news at SciBeat.
411 articles
Nearby plates
- Flexible Boron Allotrope Conducts 10 Million Times Better
- Zinc doping preserves two energy gaps in iron selenide
- Burning Iron Instead of Coal Could Give Old Power Plants a Second Life
- Gamma-Iron Phase Identified in Chang'e-6 Lunar Soil for First Time
- Layered cobalt material yields first signs of altermagnetism